Altec 169 Mhz Combined Gas & Carbon Monoxide Detector

Altec 169 Mhz Combined Gas & Carbon Monoxide Detector

Share
Our Price £264.65
Reward Points 1323
Quantity

Manufacturer Tynetec

Description

Combined Gas & Carbon Monoxide Detectors should be wall mounted above door height in all rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of gas or carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

  • Gas - Nemoto Catalytic sensor
  • CO - Electrochemical Cell sensor
  • 85 dB sounder, power, fault, gas & CO alarm LED indicators
  • Requires 240V AC mains supply via a fused spur
  • 1 Watt power consumption
  • 5 years detector life (inc transmitter battery)
  • Daily battery self test & low battery reporting
  • Dimensions: 150 x 115 x 53 mm (HxWxD)
  • Combined Gas & CO Detector Part No. ZXT427

Related Products...

Strobe Light

A flashing Strobe Light is used to alert hard of hearing residents when the Local Manager or Control Centre is trying to contact them.

Features include

  • Wall mounted enclosure: 110mm diameter x 70mm deep
  • 50mm diameter blue strobe light
  • Triggered automatically by a call to an Advent xt intercom
  • Flash duration: 20 seconds
  • Advent xt Strobe Light Part No. ZSL045
  • Compatible with Advent xt systems only

£63.06

Altec 169Mhz Carbon Monoxide Detector

Carbon Monoxide Detectors should be wall mounted above door height in rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

  • Electrochemical Cell sensor
  • 85 dB sounder, power, fault & alarm LED indicators
  • Test/Hush button
  • Monthly self test & fault warning feature
  • 5 years detector life (inc battery)
  • Daily battery self test & low battery reporting
  • Dimensions: 145 x 80 x 50 mm (HxWxD)
  • Complies with BS EN 50291: 2001
  • Carbon Monoxide Detector Part No. ZXT422
  • Compatible with SayPhone, Advent xt & Altec Response

£140.91

Epilespy Monitor

The Epilepsy Monitor bed sensor pads should be positioned under the mattress to detect arm and leg movements. If a Tonic Clonic seizure is detected in the bed an alarm call is transmitted.

Features include

  • 2 under mattress sensor pads
  • Sophisticated digital processor
  • 3 sensitivity settings
  • LED indication of sensitivity setting
  • Supplied with Mains Adapter
  • 5 Years Transmitter battery life (typical)
  • Daily battery self test & low battery reporting
  • Dimensions: 125 x 69 x 24 mm (HxWxD)
  • Epilepsy Monitor Part No. ZXT441
  • Compatible with SayPhone, Advent xt & Altec Response

Air Activated Switch

The Air Activated switch can be used in wet areas such as swimming pools or Jacuzzi's. The actuator pad is connected via PVC tubing to a wall mounted switch plate. An alarm call is made by simply squeezing the pad once.

£69.38

Altec 169Mhz Panic Button

The Bogus Caller Button is usually wall mounted in the hallway alongside the front door where it can easily be pressed if the resident feels threatened or uneasy with a visitor. When used with the SayPhone 21 it will initiate a "silent" alarm call to the Control Centre, when used with the Advent xt it will initiate an "attack" alarm call having priority over any other call in progress.

Features include

  • Momentary action pushbutton
  • Single gang pattress & surface backbox
  • Discreet - looks like a normal light switch
  • 5 years battery life (typical)
  • Daily battery self test & low battery reporting
  • Dimensions: 87 x 87 x 40 mm (HxWxD)
  • Bogus Caller/Panic Button Part No. ZXT436
  • Compatible with SayPhone, Advent xt & Altec Response

£57.15

Sensor Controller

The Sensor Controller can be used with a Bed Sensor, Chair Sensor, Pressure Mat or Door Contact. If a person gets into bed/sits in their chair, then gets up again and does not return within the preset time an alarm call will be transmitted. With the pressure mat/door contact an alarm will be transmitted 1 minute after the sensor is activated unless cancelled locally. Lamps etc. can be turned on/off automatically using a Remote Controlled Mains Switcher Kit.

Features include

  • 7 day time clock with battery back-up
  • Up to 6 monitoring periods per day
  • 10, 20 or 50 minute time-out options
  • Multifunction pushbutton and Status LED indicator
  • Test Mode to simplify set-up
  • Supplied with battery and 240V AC adaptor
  • 6 months battery life (typical)
  • Daily battery self test & low battery reporting
  • Dimensions: 35 x 85 x 170 mm (HxWxD)
  • Sensor Controller Part No. ZXT430
  • Compatible with SayPhone, Advent xt & Altec Response

£174.78

Altec 169Mhz Fall Detector

Not only can it automatically detect a fall but it can also be used to detect stumbles, trips or recovered falls. If a fall is detected the unit will enter a pre-alarm state indicated by fast beeps and a green flashing LED. If the unit is not returned to the vertical position during the pre-alarm period, an emergency alarm call will be made via an At Home Alarm Unit or Advent xt Grouped System. This results in a flashing red LED on the fall detector.

Where a stumble or a trip is detected, the unit logs this information to either a SayPhone 21 At Home Alarm unit or an Advent xt Grouped System. The data can then be accessed and analysed using Tynetec's Altera Care Software. This can then be used to look for early intervention opportunities that can ultimately lead to a reduction in emergency hospital admissions.

A normal alarm call can be made at any time by pressing the red button.

Features include

  • Solid state dual axis accelerometer sensor
  • 5 user selectable levels of sensitivity
  • 3 event logs; impacts, pre-alarms & alarms
  • 1 year battery life (typical) - user replaceable 3.6V Lithium
  • Daily battery self test & low battery reporting
  • Dimensions: 85 x 56 x 20 mm (H x W x D)
  • Weight: 68 grams
  • Range: 75 metres (typical)
  • Fall Detector Part No. ZXT410
  • Optional Elasticated Belt Part No. YW9946
  • Compatible with SayPhone, Advent xt & Altec Response

£120.38

Chair Sensor

The Chair Sensor should be positioned under the seat cushion, monitoring periods are set on the Sensor Controller. If a person sits down, then gets up again and does not return within the preset time an alarm call will be transmitted. A table lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-chair" and "out-of-chair" activity is transmitted and logged.

Features include

  • Chair sensor dimensions: 325 x 130 mm
  • 1.5 metre lead with locking plug-in connector
  • Double adapter available for 2 sensors per chair
  • 4 levels of sensitivity with auto-calibration
  • Up to 6 monitoring periods per day
  • 10, 20 or 50 minute out-of-chair timeout options
  • Chair Sensor Part No. ZCS859
  • Compatible with Tynetec Sensor Controller

£259.82

Altec 169Mhz Big Button

The Big Button switch is a free-standing unit which can be placed on a tabletop within reach of the user. An emergency alarm call can be made by pressing the button. Simply rotate the cover to increase or decrease the actuation pressure.

Features include

  • Large momentary action pushbutton
  • djustable actuation pressure (from 200g to 1.5Kg)
  • 15 preset positions
  • 5 years battery life (typical)
  • Daily battery self test & low battery reporting
  • Dimensions: 130mm diameter x 40mm high
  • Weight: 250 grams
  • Range: 75 metres (typical)
  • Big Button Callpoint Part No. ZXT439
  • Compatible with SayPhone, Advent xt & Altec Response

£88.17

More...

Send to Friend

: *
: *
: *
Type the letters you see in the picture:
Captcha

*