Altec 169Mhz Big Button

The Temperature Extreme Sensor should be wall mounted in the hallway or living room away from any draughts or heat sources. This will provide early warning of extreme low or high household temperatures which could result in the occupier suffering hypothermia or dehydration. In addition, the building will also be protected against burst pipes or potential fire hazards.

Features include

• Solid state temperature sensing element
• Lower alarm temperature: 5 degrees C for 30 minutes
• Upper alarm temperature: 30 degrees C for 5 minutes
• Rate of rise alarm temperature: 8 degrees C per minute
• 3 years battery life (typical) - user replaceable 3.6V Lithium
• Daily battery self test & low battery reporting
• Dimensions: 84 x 84 x 36 mm (HxWxD)
• Temperature Extreme Sensor Part No. ZXT426
• Compatible with SayPhone, Advent xt & Altec Response

Combined Gas & Carbon Monoxide Detectors should be wall mounted above door height in all rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of gas or carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

• Gas - Nemoto Catalytic sensor
• CO - Electrochemical Cell sensor
• 85 dB sounder, power, fault, gas & CO alarm LED indicators
• Requires 240V AC mains supply via a fused spur
• 1 Watt power consumption
• 5 years detector life (inc transmitter battery)
• Daily battery self test & low battery reporting
• Dimensions: 150 x 115 x 53 mm (HxWxD)
• Combined Gas & CO Detector Part No. ZXT427

The Ambient Temperature Monitor should be wall mounted in the hallway or living room away from any draughts or heat sources. When used in conjunction with a PIR, this device can be used to assess whether a client is potentially at risk from hypothermia e.g. if they are not using their central heating system at night or during winter months. The unit will generate a warning signal should the temperature drop below 16 degrees C and will activate an alarm condition should the temperature fall below 10 degrees C for 30 minutes.

Features include

• Solid state temperature sensing element
• Lower alarm temperature: 10 degrees C for 30 minutes
• Upper temperature threshold: 16 degrees C
• 3 years battery life (typical) - user replaceable 3.6V Lithium
• Daily battery self test & low battery reporting
• Dimensions: 84 x 84 x 36 mm (HxWxD)
• Ambient Temperature Monitor No. ZXT442
• Compatible with SayPhone, Advent xt & Altec Response

The Bed Sensor should be positioned across the width of the bed between the mattress and the base. Monitoring periods are set on the Sensor Controller. If the person gets into bed, then gets out again and does not return within the preset time an alarm call will be transmitted. A bedside lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-bed" and "out-of-bed" activity is transmitted and logged.

Features include

• Bed sensor dimensions: 650 x 130 mm
• 2 metre lead with locking plug-in connector
• Double adapter available for 2 sensors per bed
• 4 levels of sensitivity with auto-calibration
• Up to 6 monitoring periods per day
• 10, 20 or 50 minute out-of-bed timeout options
• Bed Sensor Part No. ZCS844
• Compatible with Tynetec Sensor Controller

A flashing Strobe Light is used to alert hard of hearing residents when the Local Manager or Control Centre is trying to contact them.

Features include

• Wall mounted enclosure: 110mm diameter x 70mm deep
• 50mm diameter blue strobe light
• Triggered automatically by a call to an Advent xt intercom
• Flash duration: 20 seconds
• Advent xt Strobe Light Part No. ZSL045
• Compatible with Advent xt systems only

Flood Detectors should be located on the floor below the bath, wash basin or kitchen sink or anywhere a tap could be left running. Flood Detectors can be free standing or screw fixed to the skirting board with an optional mounting bracket. If a flood is detected an alarm call will be transmitted.

Features include

• Moisture Bridge Sensor
• Activated LED indicator
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 50 x 95 x 18 mm (HxWxD)
• Flood Detector Part No. ZXT424
• Optional Mounting Bracket Part No. V00770
• Compatible with SayPhone, Advent xt & Altec Response

The Air Activated switch can be used in wet areas such as swimming pools or Jacuzzi's. The actuator pad is connected via PVC tubing to a wall mounted switch plate. An alarm call is made by simply squeezing the pad once.

The Pill Dispenser will sound an alarm when it is time for the user to take their medication - if the pills are not taken from the dispenser within a preset period an alarm call will be transmitted. The Pill Dispenser will make the correct dosage available at the correct time each day whilst keeping the others locked out of sight.Pills "ready" and pills "taken" times are also transmitted and logged

Features include

• 1 to 28 day capacity - 1 to 28 doses per day
• Lockable lid (supplied with 2 keys)
• LCD display and easy to navigate programming menus
• Audible alarm & flashing LED when pills "ready"
• Self Test mode for easy registration
• 12 months battery life (typical)
• 4 user replaceable AA batteries
• Daily battery self test & low battery reporting
• Dimensions: 180mm diameter x 50mm deep
• Weight: 480 grams (empty)
• Pill Dispenser Part No. ZXT432
• Spare Cassette Part No. W00359
• Compatible with SayPhone, Advent xt & Altec Response

The Double Adapter can be used to connect 2 Bed Sensors (i.e. in a double bed) or 2 Pressure Mats/Door Contacts to a single Sensor Controller.

Features Include

• Fully connected RJ45 splitter
• Simple plug-in connection
• Double Adapter Part No. P10285
• Compatible with Tynetec Sensor Controller