Altec 169Mhz Pullcord

The Temperature Extreme Sensor should be wall mounted in the hallway or living room away from any draughts or heat sources. This will provide early warning of extreme low or high household temperatures which could result in the occupier suffering hypothermia or dehydration. In addition, the building will also be protected against burst pipes or potential fire hazards.

Features include

• Solid state temperature sensing element
• Lower alarm temperature: 5 degrees C for 30 minutes
• Upper alarm temperature: 30 degrees C for 5 minutes
• Rate of rise alarm temperature: 8 degrees C per minute
• 3 years battery life (typical) - user replaceable 3.6V Lithium
• Daily battery self test & low battery reporting
• Dimensions: 84 x 84 x 36 mm (HxWxD)
• Temperature Extreme Sensor Part No. ZXT426
• Compatible with SayPhone, Advent xt & Altec Response

Carbon Monoxide Detectors should be wall mounted above door height in rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

• Electrochemical Cell sensor
• 85 dB sounder, power, fault & alarm LED indicators
• Test/Hush button
• Monthly self test & fault warning feature
• 5 years detector life (inc battery)
• Daily battery self test & low battery reporting
• Dimensions: 145 x 80 x 50 mm (HxWxD)
• Complies with BS EN 50291: 2001
• Carbon Monoxide Detector Part No. ZXT422
• Compatible with SayPhone, Advent xt & Altec Response

PIR Movement Detectors should be wall mounted at high level in the hallway or living room to monitor movement within the dwelling. PIR's can be used for activity monitoring or intruder detection;

Activity Mode; if no movement is detected within a preset period an "inactivity" alarm call will be transmitted.

Intruder Mode; if movement is detected an "intruder" alarm call will be transmitted.

Features include

• Passive Infra Red sensor
• Walk Test LED indicator
• 2 minute signal time mask to prolong battery life
• Pet Alley option to prevent false calls from pets
• 1 year battery life (typical with 9V Lithium battery)
• Daily battery self test & low battery reporting
• Dimensions: 114 x 70 x 76 mm (HxWxD)
• PIR Movement Detector Part No. ZXT425
• Compatible with SayPhone and Advent xt systems

The Bogus Caller Button is usually wall mounted in the hallway alongside the front door where it can easily be pressed if the resident feels threatened or uneasy with a visitor. When used with the SayPhone 21 it will initiate a "silent" alarm call to the Control Centre, when used with the Advent xt it will initiate an "attack" alarm call having priority over any other call in progress.

Features include

• Momentary action pushbutton
• Single gang pattress & surface backbox
• Discreet - looks like a normal light switch
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 87 x 87 x 40 mm (HxWxD)
• Bogus Caller/Panic Button Part No. ZXT436
• Compatible with SayPhone, Advent xt & Altec Response

The Bed Sensor should be positioned across the width of the bed between the mattress and the base. Monitoring periods are set on the Sensor Controller. If the person gets into bed, then gets out again and does not return within the preset time an alarm call will be transmitted. A bedside lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-bed" and "out-of-bed" activity is transmitted and logged.

Features include

• Bed sensor dimensions: 650 x 130 mm
• 2 metre lead with locking plug-in connector
• Double adapter available for 2 sensors per bed
• 4 levels of sensitivity with auto-calibration
• Up to 6 monitoring periods per day
• 10, 20 or 50 minute out-of-bed timeout options
• Bed Sensor Part No. ZCS844
• Compatible with Tynetec Sensor Controller

The Air Activated switch can be used in wet areas such as swimming pools or Jacuzzi's. The actuator pad is connected via PVC tubing to a wall mounted switch plate. An alarm call is made by simply squeezing the pad once.

The Keypad should be wall mounted within the dwelling with the contacts wired to the door and the mains adapter plugged into a 13A socket. Before the Carer leaves they enter a code to start the exit time period. When the exit time period expires the door is armed. When the door is opened the entry time period starts. If the code is not entered within the entry time an alarm call will be transmitted.

Features include

• Programmable 4 digit arm/disarm code
• Programmable entry & exit times
• Integral entry/exit sounder
• Instant alarm zone option
• Flip-cover & illuminated keypad
• Test facility
• Supplied with mains adapter & door contacts
• 5 years transmitter battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 135 x 90 x 27 mm (HxWxD)
• Wandering Alarm Part No. ZXT433
• Compatible with SayPhone, Advent xt & Altec Response

The Double Adapter can be used to connect 2 Bed Sensors (i.e. in a double bed) or 2 Pressure Mats/Door Contacts to a single Sensor Controller.

Features Include

• Fully connected RJ45 splitter
• Simple plug-in connection
• Double Adapter Part No. P10285
• Compatible with Tynetec Sensor Controller

Combined Gas & Carbon Monoxide Detectors should be wall mounted above door height in all rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of gas or carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

• Gas - Nemoto Catalytic sensor
• CO - Electrochemical Cell sensor
• 85 dB sounder, power, fault, gas & CO alarm LED indicators
• Requires 240V AC mains supply via a fused spur
• 1 Watt power consumption
• 5 years detector life (inc transmitter battery)
• Daily battery self test & low battery reporting
• Dimensions: 150 x 115 x 53 mm (HxWxD)
• Combined Gas & CO Detector Part No. ZXT427