Bed Sensor

Bed Sensor

Share
Our Price £279.02
Reward Points 1395
Quantity

Manufacturer Tynetec

Description

The Bed Sensor should be positioned across the width of the bed between the mattress and the base. Monitoring periods are set on the Sensor Controller. If the person gets into bed, then gets out again and does not return within the preset time an alarm call will be transmitted. A bedside lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-bed" and "out-of-bed" activity is transmitted and logged.

Features include

  • Bed sensor dimensions: 650 x 130 mm
  • 2 metre lead with locking plug-in connector
  • Double adapter available for 2 sensors per bed
  • 4 levels of sensitivity with auto-calibration
  • Up to 6 monitoring periods per day
  • 10, 20 or 50 minute out-of-bed timeout options
  • Bed Sensor Part No. ZCS844
  • Compatible with Tynetec Sensor Controller

Related Products...

Altec 169 Mhz Combined Gas & Carbon Monoxide Detector

Combined Gas & Carbon Monoxide Detectors should be wall mounted above door height in all rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of gas or carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

  • Gas - Nemoto Catalytic sensor
  • CO - Electrochemical Cell sensor
  • 85 dB sounder, power, fault, gas & CO alarm LED indicators
  • Requires 240V AC mains supply via a fused spur
  • 1 Watt power consumption
  • 5 years detector life (inc transmitter battery)
  • Daily battery self test & low battery reporting
  • Dimensions: 150 x 115 x 53 mm (HxWxD)
  • Combined Gas & CO Detector Part No. ZXT427

£264.65

Strobe Light

A flashing Strobe Light is used to alert hard of hearing residents when the Local Manager or Control Centre is trying to contact them.

Features include

  • Wall mounted enclosure: 110mm diameter x 70mm deep
  • 50mm diameter blue strobe light
  • Triggered automatically by a call to an Advent xt intercom
  • Flash duration: 20 seconds
  • Advent xt Strobe Light Part No. ZSL045
  • Compatible with Advent xt systems only

£63.06

Altec 169Mhz Heat Detector

Heat Detectors should be ceiling mounted in kitchens or areas with high levels of fumes or dust, they are not suitable for bathrooms or areas of high humidity. When activated a local alarm will sound and an alarm call will be transmitted. The Control Centre or Local Manager can speak with the resident and assess the risk before contacting the Emergency Services.

Features include

  • Fast responding Thermistor sensor
  • 85 dB sounder
  • Test Button and status LED indicator
  • 1 year battery life (typical) - user replaceable 9V PP3
  • Daily battery self test & low battery reporting
  • Dimensions: 120 x 135 x 55 mm (HxWxD)
  • Complies with BS 415: 1990
  • Heat Detector Part No. ZXT421
  • Compatible with SayPhone, Advent xt & Altec Response

£100.71

Door Contact

The Door Contacts can be used to monitor any controlled door. If the door is opened with the keyswitch in the "Normal" position an alarm call will be transmitted. If the door needs to be opened for a genuine reason the keyswitch can be turned to the "Override" position.

Features include

  • Surface mount single gang pattress
  • 2 position Keyswitch (2 keys supplied)
  • Key removable in both positions
  • N/O surface mount door contacts supplied
  • 5 years battery life (typical)
  • Daily battery self test & low battery reporting
  • Dimensions: 87 x 87 x 40 mm (HxWxD)
  • Door Alarm & Keyswitch Part No. ZXT438
  • Compatible with SayPhone, Advent xt & Altec Response

£59.32

Altec 169 Mhz Temp Extreme Sensor

The Temperature Extreme Sensor should be wall mounted in the hallway or living room away from any draughts or heat sources. This will provide early warning of extreme low or high household temperatures which could result in the occupier suffering hypothermia or dehydration. In addition, the building will also be protected against burst pipes or potential fire hazards.

Features include

  • Solid state temperature sensing element
  • Lower alarm temperature: 5 degrees C for 30 minutes
  • Upper alarm temperature: 30 degrees C for 5 minutes
  • Rate of rise alarm temperature: 8 degrees C per minute
  • 3 years battery life (typical) - user replaceable 3.6V Lithium
  • Daily battery self test & low battery reporting
  • Dimensions: 84 x 84 x 36 mm (HxWxD)
  • Temperature Extreme Sensor Part No. ZXT426
  • Compatible with SayPhone, Advent xt & Altec Response

£99.52

Altec 169Mhz Pullcord

Ceiling Pullcord switches can be fitted in bathrooms, alongside the bed or anywhere Personal Pendants are not usually worn. An alarm call is made by simply pulling the cord once. The cord is long enough to reach floor level. Pullcord switches are available as radio or hardwired.

Features include

  • 2.7 metre orange nylon cord
  • 2 triangular orange grips
  • 5 years battery life (typical)
  • Daily battery self test & low battery reporting
  • Dimensions: 85mm diameter x 40 mm deep
  • Radio Pullcord Part No. ZXT435
  • Standard Hardwired Pullcord Part No. S00510
  • Compatible with SayPhone, Advent xt & Altec Response

£78.55

Enuresis Sensor

The Enuresis Sensor comprises of a Bed Mat and an Interface Unit. The Bed Mat should be placed between the bottom sheet and the mattress with the cable plugged into the Interface Unit. If moisture is detected in the bed an alarm call will be transmitted.

Features include

  • Foil embossed plastic bed mat
  • 2.2 metre lead with locking plug-in connector
  • Activated LED indicator
  • 3 Years battery life (typical)
  • Daily battery self test & low battery reporting
  • Interface dimensions: 90 x 65 x 28 mm (HxWxD)
  • Bed Mat dimensions: 540 x 420 mm
  • Enuresis Sensor Part No. ZXT431(inc interface and 5 bed mats)
  • Spare Bed Mats Part No. E00550 (pack of 5)
  • Compatible with SayPhone, Advent xt & Altec Response

£163.03

Double Adaptor

The Double Adapter can be used to connect 2 Bed Sensors (i.e. in a double bed) or 2 Pressure Mats/Door Contacts to a single Sensor Controller.

Features Include

  • Fully connected RJ45 splitter
  • Simple plug-in connection
  • Double Adapter Part No. P10285
  • Compatible with Tynetec Sensor Controller

£14.48

Vibrating Pad

The Vibrating Pad can be used under a pillow or cushion to alert hard of hearing residents when the Local Manager or Control Centre is trying to contact them.

Features include

  • 100mm diameter vibrating pad
  • 1.5 metre lead with locking jack plug
  • Supplied with single gang wall plate & jack socket
  • Triggered automatically by a call to an Advent xt intercom
  • Connects to Strobe Light or separate interface board
  • Vibrating Pad Part No. W00360
  • Optional interface (if used without strobe) Part No. A00452
  • Compatible with Advent XT systems only

More...

Send to Friend

: *
: *
: *
Type the letters you see in the picture:
Captcha

*