Epilespy Monitor
Description
|
The Epilepsy Monitor bed sensor pads should be positioned under the mattress to detect arm and leg movements. If a Tonic Clonic seizure is detected in the bed an alarm call is transmitted. Features include
|
Related Products...
Altec 169Mhz Big Button
|
The Big Button switch is a free-standing unit which can be placed on a tabletop within reach of the user. An emergency alarm call can be made by pressing the button. Simply rotate the cover to increase or decrease the actuation pressure. Features include
|
£88.17
Enuresis Sensor
|
The Enuresis Sensor comprises of a Bed Mat and an Interface Unit. The Bed Mat should be placed between the bottom sheet and the mattress with the cable plugged into the Interface Unit. If moisture is detected in the bed an alarm call will be transmitted. Features include
|
£163.03
Double Adaptor
|
The Double Adapter can be used to connect 2 Bed Sensors (i.e. in a double bed) or 2 Pressure Mats/Door Contacts to a single Sensor Controller. Features Include
|
£14.48
Wander Alarm
|
The Keypad should be wall mounted within the dwelling with the contacts wired to the door and the mains adapter plugged into a 13A socket. Before the Carer leaves they enter a code to start the exit time period. When the exit time period expires the door is armed. When the door is opened the entry time period starts. If the code is not entered within the entry time an alarm call will be transmitted. Features include
|
Altec 169Mhz Panic Button
|
The Bogus Caller Button is usually wall mounted in the hallway alongside the front door where it can easily be pressed if the resident feels threatened or uneasy with a visitor. When used with the SayPhone 21 it will initiate a "silent" alarm call to the Control Centre, when used with the Advent xt it will initiate an "attack" alarm call having priority over any other call in progress. Features include
|
£57.15
Bed Sensor
|
The Bed Sensor should be positioned across the width of the bed between the mattress and the base. Monitoring periods are set on the Sensor Controller. If the person gets into bed, then gets out again and does not return within the preset time an alarm call will be transmitted. A bedside lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-bed" and "out-of-bed" activity is transmitted and logged. Features include
|
£279.02
Air Activated Switch
|
The Air Activated switch can be used in wet areas such as swimming pools or Jacuzzi's. The actuator pad is connected via PVC tubing to a wall mounted switch plate. An alarm call is made by simply squeezing the pad once. |
£69.38
Altec 169Mhz Fall Detector
|
Not only can it automatically detect a fall but it can also be used to detect stumbles, trips or recovered falls. If a fall is detected the unit will enter a pre-alarm state indicated by fast beeps and a green flashing LED. If the unit is not returned to the vertical position during the pre-alarm period, an emergency alarm call will be made via an At Home Alarm Unit or Advent xt Grouped System. This results in a flashing red LED on the fall detector. Where a stumble or a trip is detected, the unit logs this information to either a SayPhone 21 At Home Alarm unit or an Advent xt Grouped System. The data can then be accessed and analysed using Tynetec's Altera Care Software. This can then be used to look for early intervention opportunities that can ultimately lead to a reduction in emergency hospital admissions. A normal alarm call can be made at any time by pressing the red button. Features include
|
£120.38
Altec 169Mhz Flood Detector
|
Flood Detectors should be located on the floor below the bath, wash basin or kitchen sink or anywhere a tap could be left running. Flood Detectors can be free standing or screw fixed to the skirting board with an optional mounting bracket. If a flood is detected an alarm call will be transmitted. Features include
|
£58.37
