Due to the current situation regarding the Covid-19 outbreak, The Directors of Saturn Sales & Services Ltd. would like to ask for your understanding with regards to all web site orders placed.
Saturn will continue to support the Health Care Industry with regards to the supply of necessary equipment and emergency system backup. However, as advised by our Government we are operating with a reduced staffing level. We therefore ask all our clients to accept that on some occasions it may not be possible to deliver orders for the next day. Please be assured that we will continue to support you as well as we can during this difficult time.
Saturn would also like to send its most grateful thanks to all of you Healthcare workers on the front line. You are the real heroes!
L714 Remote Sounder with Relay
Description
|
If you need an audible alarm to attract attention, but don't need an indication of the call location, the L714 is the simple solution. The sounder is similar in operation to a display unit with a multi level alarm, but has limited zoning facilities. Any assistance or emergency call on the system will over-ride the standard call tone. A built-in relay provides normally open and normally closed 'dry' contacts, which can be used to trigger auxiliary devices. |
Related Products...
SW1 Day/Night Volume Control Switch
|
Manual control switch to allow volumes to be quieter at night or when required. |
£25.00
L628 LCD Display Units
|
Designed to give clear indication and alarm at every monitoring location. The unit features an LCD display with backlight, multi-level adjustable alarm, day/night volume control, 'priority' alarm tone for specific call locations, configuration menus and an output which can be connected to trigger external equipment. All displays work identically but can be configured on-site to operate independently. |
£155.00
SCP Slave Call Point
|
Designed for use in one room or ward where each individual bed doesn't need a separate identity on the call system. The unit features a call button, pear lead jack socket and re-assurance indicator. Units must be connected to a standard call point to generate the call identity and to provide the reset. Slave call points can only generate a standard call from either the call button or pear lead socket. |
£24.00
L730 Slave Infra-Red Unit
|
Slave infra-red receiver which can be linked into other call points. |
£46.50
L746 Overdoor Light
|
These are normally positioned above doors in a corridor to indicate the status of the call point(s) within each room. The L746 can also be used to monitor several call points for end of corridor indication, or as a 'follow me' light. Each unit is fitted with twin ultra-bright LEDs which mimic the reassurance indicator on the call points. Also available with an integral sounder alarm (L746S). |
£33.50
Fused Junction Board
|
The FJB2 provides four 'spur' outputs from the network spine with each output incorporating an over current/voltage and reverse polarity protection device. A front panel mounted red/green LED indicates the condition of the internal fuses and continuously monitors the network data signals. Individual fuse failure LEDs are mounted on the reverse of the unit and in the event of cable fault, on one of the outputs, the 'spur' will be isolated without disbaling the entire cable network. |
£38.50
L622M Standard Call Point with Magnetic Reset
|
The L622M is the magnetic reset version of the standard call point. It is non-audio and can generate up to 6 independent call levels indicated by the twin colour re-assurance LED. The 'call follower' sounder whih is activated when the call point is in 'staff present' mode, alerts staff to other calls on the system. The jack socket will accept any closing contact input from pear leads, pressure mats, radio triggers and a host of other trigger devices. |
£72.50
L634 Network Input/Output Module
|
The L634 is used to interface an external device to the Intercall system network. The unit features three input triggers: two non-latching and one remote reset and two outputs; Re-assurance LED & open collector which can be used to trigger external equipment for normal or emergency calls. Typical applications include telephone ring detectors, contacts from fire alarm or other control panels or input from remote contacts etc. It may also be used to link two independent Intercall systems together to allo signalling, such that an active alarm on one system triggers a call on the other system and vice versa. |
£75.00
