PIR Movement Detector

A flashing Strobe Light is used to alert hard of hearing residents when the Local Manager or Control Centre is trying to contact them.

Features include

• Wall mounted enclosure: 110mm diameter x 70mm deep
• 50mm diameter blue strobe light
• Triggered automatically by a call to an Advent xt intercom
• Flash duration: 20 seconds
• Advent xt Strobe Light Part No. ZSL045
• Compatible with Advent xt systems only

The Door Contacts can be used to monitor any controlled door. If the door is opened with the keyswitch in the "Normal" position an alarm call will be transmitted. If the door needs to be opened for a genuine reason the keyswitch can be turned to the "Override" position.

Features include

• Surface mount single gang pattress
• 2 position Keyswitch (2 keys supplied)
• Key removable in both positions
• N/O surface mount door contacts supplied
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 87 x 87 x 40 mm (HxWxD)
• Door Alarm & Keyswitch Part No. ZXT438
• Compatible with SayPhone, Advent xt & Altec Response

The Air Activated switch can be used in wet areas such as swimming pools or Jacuzzi's. The actuator pad is connected via PVC tubing to a wall mounted switch plate. An alarm call is made by simply squeezing the pad once.

The Bed Sensor should be positioned across the width of the bed between the mattress and the base. Monitoring periods are set on the Sensor Controller. If the person gets into bed, then gets out again and does not return within the preset time an alarm call will be transmitted. A bedside lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-bed" and "out-of-bed" activity is transmitted and logged.

Features include

• Bed sensor dimensions: 650 x 130 mm
• 2 metre lead with locking plug-in connector
• Double adapter available for 2 sensors per bed
• 4 levels of sensitivity with auto-calibration
• Up to 6 monitoring periods per day
• 10, 20 or 50 minute out-of-bed timeout options
• Bed Sensor Part No. ZCS844
• Compatible with Tynetec Sensor Controller

Flood Detectors should be located on the floor below the bath, wash basin or kitchen sink or anywhere a tap could be left running. Flood Detectors can be free standing or screw fixed to the skirting board with an optional mounting bracket. If a flood is detected an alarm call will be transmitted.

Features include

• Moisture Bridge Sensor
• Activated LED indicator
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 50 x 95 x 18 mm (HxWxD)
• Flood Detector Part No. ZXT424
• Optional Mounting Bracket Part No. V00770
• Compatible with SayPhone, Advent xt & Altec Response

Ceiling Pullcord switches can be fitted in bathrooms, alongside the bed or anywhere Personal Pendants are not usually worn. An alarm call is made by simply pulling the cord once. The cord is long enough to reach floor level. Pullcord switches are available as radio or hardwired.

Features include

• 2.7 metre orange nylon cord
• 2 triangular orange grips
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 85mm diameter x 40 mm deep
• Radio Pullcord Part No. ZXT435
• Standard Hardwired Pullcord Part No. S00510
• Compatible with SayPhone, Advent xt & Altec Response

The Enuresis Sensor comprises of a Bed Mat and an Interface Unit. The Bed Mat should be placed between the bottom sheet and the mattress with the cable plugged into the Interface Unit. If moisture is detected in the bed an alarm call will be transmitted.

Features include

• Foil embossed plastic bed mat
• 2.2 metre lead with locking plug-in connector
• Activated LED indicator
• 3 Years battery life (typical)
• Daily battery self test & low battery reporting
• Interface dimensions: 90 x 65 x 28 mm (HxWxD)
• Bed Mat dimensions: 540 x 420 mm
• Enuresis Sensor Part No. ZXT431(inc interface and 5 bed mats)
• Spare Bed Mats Part No. E00550 (pack of 5)
• Compatible with SayPhone, Advent xt & Altec Response

The Bogus Caller Button is usually wall mounted in the hallway alongside the front door where it can easily be pressed if the resident feels threatened or uneasy with a visitor. When used with the SayPhone 21 it will initiate a "silent" alarm call to the Control Centre, when used with the Advent xt it will initiate an "attack" alarm call having priority over any other call in progress.

Features include

• Momentary action pushbutton
• Single gang pattress & surface backbox
• Discreet - looks like a normal light switch
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 87 x 87 x 40 mm (HxWxD)
• Bogus Caller/Panic Button Part No. ZXT436
• Compatible with SayPhone, Advent xt & Altec Response

The Vibrating Pad can be used under a pillow or cushion to alert hard of hearing residents when the Local Manager or Control Centre is trying to contact them.

Features include

• 100mm diameter vibrating pad
• 1.5 metre lead with locking jack plug
• Supplied with single gang wall plate & jack socket
• Triggered automatically by a call to an Advent xt intercom
• Connects to Strobe Light or separate interface board
• Vibrating Pad Part No. W00360
• Optional interface (if used without strobe) Part No. A00452
• Compatible with Advent XT systems only