Strobe Light

Combined Gas & Carbon Monoxide Detectors should be wall mounted above door height in all rooms that contain a fuel burning appliance. Do not fit in bathrooms, directly above cookers or in draughty areas. If a dangerous level of gas or carbon monoxide is detected a local alarm will sound and an alarm call will be transmitted.

Features include

• Gas - Nemoto Catalytic sensor
• CO - Electrochemical Cell sensor
• 85 dB sounder, power, fault, gas & CO alarm LED indicators
• Requires 240V AC mains supply via a fused spur
• 1 Watt power consumption
• 5 years detector life (inc transmitter battery)
• Daily battery self test & low battery reporting
• Dimensions: 150 x 115 x 53 mm (HxWxD)
• Combined Gas & CO Detector Part No. ZXT427

The Sensor Controller can be used with a Bed Sensor, Chair Sensor, Pressure Mat or Door Contact. If a person gets into bed/sits in their chair, then gets up again and does not return within the preset time an alarm call will be transmitted. With the pressure mat/door contact an alarm will be transmitted 1 minute after the sensor is activated unless cancelled locally. Lamps etc. can be turned on/off automatically using a Remote Controlled Mains Switcher Kit.

Features include

• 7 day time clock with battery back-up
• Up to 6 monitoring periods per day
• 10, 20 or 50 minute time-out options
• Multifunction pushbutton and Status LED indicator
• Test Mode to simplify set-up
• Supplied with battery and 240V AC adaptor
• 6 months battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 35 x 85 x 170 mm (HxWxD)
• Sensor Controller Part No. ZXT430
• Compatible with SayPhone, Advent xt & Altec Response

Flood Detectors should be located on the floor below the bath, wash basin or kitchen sink or anywhere a tap could be left running. Flood Detectors can be free standing or screw fixed to the skirting board with an optional mounting bracket. If a flood is detected an alarm call will be transmitted.

Features include

• Moisture Bridge Sensor
• Activated LED indicator
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 50 x 95 x 18 mm (HxWxD)
• Flood Detector Part No. ZXT424
• Optional Mounting Bracket Part No. V00770
• Compatible with SayPhone, Advent xt & Altec Response

Ceiling Pullcord switches can be fitted in bathrooms, alongside the bed or anywhere Personal Pendants are not usually worn. An alarm call is made by simply pulling the cord once. The cord is long enough to reach floor level. Pullcord switches are available as radio or hardwired.

Features include

• 2.7 metre orange nylon cord
• 2 triangular orange grips
• 5 years battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 85mm diameter x 40 mm deep
• Radio Pullcord Part No. ZXT435
• Standard Hardwired Pullcord Part No. S00510
• Compatible with SayPhone, Advent xt & Altec Response

The Keypad should be wall mounted within the dwelling with the contacts wired to the door and the mains adapter plugged into a 13A socket. Before the Carer leaves they enter a code to start the exit time period. When the exit time period expires the door is armed. When the door is opened the entry time period starts. If the code is not entered within the entry time an alarm call will be transmitted.

Features include

• Programmable 4 digit arm/disarm code
• Programmable entry & exit times
• Integral entry/exit sounder
• Instant alarm zone option
• Flip-cover & illuminated keypad
• Test facility
• Supplied with mains adapter & door contacts
• 5 years transmitter battery life (typical)
• Daily battery self test & low battery reporting
• Dimensions: 135 x 90 x 27 mm (HxWxD)
• Wandering Alarm Part No. ZXT433
• Compatible with SayPhone, Advent xt & Altec Response

The Enuresis Sensor comprises of a Bed Mat and an Interface Unit. The Bed Mat should be placed between the bottom sheet and the mattress with the cable plugged into the Interface Unit. If moisture is detected in the bed an alarm call will be transmitted.

Features include

• Foil embossed plastic bed mat
• 2.2 metre lead with locking plug-in connector
• Activated LED indicator
• 3 Years battery life (typical)
• Daily battery self test & low battery reporting
• Interface dimensions: 90 x 65 x 28 mm (HxWxD)
• Bed Mat dimensions: 540 x 420 mm
• Enuresis Sensor Part No. ZXT431(inc interface and 5 bed mats)
• Spare Bed Mats Part No. E00550 (pack of 5)
• Compatible with SayPhone, Advent xt & Altec Response

Not only can it automatically detect a fall but it can also be used to detect stumbles, trips or recovered falls. If a fall is detected the unit will enter a pre-alarm state indicated by fast beeps and a green flashing LED. If the unit is not returned to the vertical position during the pre-alarm period, an emergency alarm call will be made via an At Home Alarm Unit or Advent xt Grouped System. This results in a flashing red LED on the fall detector.

Where a stumble or a trip is detected, the unit logs this information to either a SayPhone 21 At Home Alarm unit or an Advent xt Grouped System. The data can then be accessed and analysed using Tynetec's Altera Care Software. This can then be used to look for early intervention opportunities that can ultimately lead to a reduction in emergency hospital admissions.

A normal alarm call can be made at any time by pressing the red button.

Features include

• Solid state dual axis accelerometer sensor
• 5 user selectable levels of sensitivity
• 3 event logs; impacts, pre-alarms & alarms
• 1 year battery life (typical) - user replaceable 3.6V Lithium
• Daily battery self test & low battery reporting
• Dimensions: 85 x 56 x 20 mm (H x W x D)
• Weight: 68 grams
• Range: 75 metres (typical)
• Fall Detector Part No. ZXT410
• Optional Elasticated Belt Part No. YW9946
• Compatible with SayPhone, Advent xt & Altec Response

The Chair Sensor should be positioned under the seat cushion, monitoring periods are set on the Sensor Controller. If a person sits down, then gets up again and does not return within the preset time an alarm call will be transmitted. A table lamp can be turned on/off automatically using a Remote Controlled Mains Switcher Kit. All "in-chair" and "out-of-chair" activity is transmitted and logged.

Features include

• Chair sensor dimensions: 325 x 130 mm
• 1.5 metre lead with locking plug-in connector
• Double adapter available for 2 sensors per chair
• 4 levels of sensitivity with auto-calibration
• Up to 6 monitoring periods per day
• 10, 20 or 50 minute out-of-chair timeout options
• Chair Sensor Part No. ZCS859
• Compatible with Tynetec Sensor Controller

The Double Adapter can be used to connect 2 Bed Sensors (i.e. in a double bed) or 2 Pressure Mats/Door Contacts to a single Sensor Controller.

Features Include

• Fully connected RJ45 splitter
• Simple plug-in connection
• Double Adapter Part No. P10285
• Compatible with Tynetec Sensor Controller